What Size Allen Wrench For Kitchen Faucet Handle?

What size Allen Wrench for kitchen faucet handle can be helpful for us? Well, it depends on what faucet you acquire.

The most common size that adjusts with almost all kitchen faucets, is a 7/64 Allen Wrench. It may not suit your faucet if you acquire a Delta faucet or a Pot filler faucet.

Anyways, it’s also important for us to get affiliated with all sizes of an Allen Wrench. And if you want to tighten or lose the mounting nuts of your faucets by yourself, you will also get to know that in this article.

So have a look below to know the perfect size of hex key for your kitchen faucet.

Allen Wrench Sizes:

Allen Wrench

What Size Allen Wrench For Kitchen Faucet Handle Used Mostly?

Well, in most cases users use an Allen Wrench of 7/64, especially for the kitchen faucet handles. For instance, users also question what size Allen Wrench to tighten the Moen kitchen faucet handle is going to be suitable.

In this case, also, the 7/64 hex wrench tends to be the best alternative.

For other kitchen faucets, like- The pull down kitchen faucet and Pull Out kitchen faucet use the 7/64 Allen wrench to tighten the handles.

However, it sometimes varies on the models too.

For example- the Kohler kitchen faucet handles require a 4mm Allen key. Again, the Pot filler Kitchen Faucet Handle goes with a 2.5 mm hex wrench.

The Delta faucet requires a 3/32″ Allen Wrench. This is how the measurement of Allen wrenches differs for kitchen faucets.

What Size Allen Wrench For Kitchen Faucet Handle Is Used Mostly

How To Use Allen Wrench For Kitchen Faucet Handle?

In order to tighten your kitchen faucet handle, you must be ready with a dowel rod 6 inches long. And its thickness should be either 1 inch or ¾ inch. Since the softer Woods wear out easily, don’t go for that. Try to use a hardwood dowel, like- oak.

Besides, you will need a grinder, vise, hammer, hand saw, two screws, a small chisel, a drill, and a drill bit. If you want, you can use a hacksaw instead of a bolt cutter.

So now we are ready with all the essentials. Let’s hit up the steps:

Cut The Dowel:

You don’t have to cut the dowel perfectly, just make the incision in half long ways. It would be much better if you cut it closer.

When you will be cutting the dowel make sure you are cutting only the bottom of it in a vise. And of course, the bottom of the doubles should remain connected and the upper part should be cut 4 inches long.

Determine The Length of Your Faucet Handle:

Prior to determining the length of your faucet handle, make sure you are leaving enough room at the end of it. Hence, you can insert the screw easily and no wood will split even.

We are already done cutting the handle. So now, we have a dowel’s two halves that are going to fit nicely for sure.

Fit Your Allen Wrench:

Strike the center of one-half of the dowel. Then see where the short side of your Allen wrench is so that you can remove wood from it. To do so, you will need a small chisel. If the wood is not removed from your Allen wrench, it may fail to fit into the slot.

Put The Handle Together:

In the next step, you will need to insert the screws. But before that, drill some holes at the end of your handles. When you are doing it, make sure the grill does not reach both sides, the other side should remain apart.

Now it’s time to insert the screws. Go for that excuse that has a shorter dimension than the handle’s width.

Make It Smooth:

Now make the screws smooth enough using a grinder or a file and remove all the splinters with sand. This is all. Your handle is all set to use.

Frequently Asked Questions

What Size of The Wrench Will You Need To Change A Faucet?

Basin wrenches are usually self-tightening and are available in various sizes. If you want to get a wrench with a telescoping shank, you will get them in a dimension of 10 inches to 17 inches. Again, these wrenches have adjustable heads ranging from 0.75 inches to 1.75 inches.

What Type of Wrench Is Good For Changing A Kitchen Faucet?

There are two tools that you can’t avoid for changing your kitchen faucet, e.g. adjustable wrench and a basin wrench. The adjustable wrench would be handy while giving the desired leverage.

You can disconnect water supply lines and unscrew all nuts with them. On the other hand, a basin wrench would be handy if you want to work in tight spaces.

Conclusion

Hopefully, the concept of what size Allen Wrench for the kitchen faucet handle would be the best option for us, is clear now. I think the 7/64 hex key is the suitable one for most sinks.

This would be the preferable size for Moen, Pull Down, Pull Out, Commer Style, and many other facets that work well with a 7/64 Allen wrench for their handles. Conversely, the Delta, Pot Filler, and some limited faucets require a different size of Allen wrench for their handles.

By following this concept you will surely not find any hassle while tightening or loosening the mounting nuts of your sink.

Thanks for reading!

Leave a Comment