How To Install A Kitchen Faucet Without Using The Sprayer?

Ways to install a kitchen faucet without using the sprayer, In order to install a kitchen faucet without a sprayer, you just need to skip installing the sprayer. Again, you will need a single-handle faucet for better results.

Afterward, you shall remove the faucet connections, remove the old faucet, get a new faucet, connect its supply lines, and check for leakages.

This article will tell you more precisely about this concept.

How To Install A Kitchen Faucet Without Using The Sprayer? (12 Ways)

The below steps will guide you in installing a kitchen faucet without using a sprayer.

Prepare Your Supplies:

Start by cleaning everything beneath the sink. Then keep a pan and some towels ready to absorb water. Most sinks have an electrical outlet which needs to be turned off during operations. Also, remember to restore power only after you have tested the new faucet for leaks

It would be better if you wear safety glasses as the dirt can get into your eyes. Use a flashlight too for better visibility inside the deep cabinet.

Turn Off The Water:

Now reach to turn the hot and cold water valves to shut them off. How many turns you will need to do depends on the type of valve. Just make sure the water has been completely turned off.

If you haven’t used your kitchen faucet’s valve in a while, it may get hard to turn. In that case, you can use a rag or a pair of pliers. This will improve your grip.

Open up the faucet handles by keeping the water turned off. It will relieve the pressure from the lines.

Disconnect The Supply Lines:

To remove the old faucet, you will first need to go under the sink. Then disconnect the supply lines down to the hot and cold valves.

The supply lines are usually connected by a threaded nut. You will need to remove those nuts. You can also take the help of an adjustable wrench. While doing it, you must make sure to stabilize the water pipe. Or else, there will be some disturbed connections behind the cabinet.

Now, you will see some water is draining out. For this reason, you must keep a pan ready with you.

We made the process for one side. On the other side, you have to repeat the same process. If the valve drips even after the water is completely off, it means the valve is faulty. At that time, you should replace it as early as possible.

Remove The Faucet Connections:

You will need to take out the old supply line connections before you remove the faucet. Between the two handles below, you will see two water supply lines connected to the hot and cold water valves. Besides, the mounting nuts are secured first. So it would be better if you unscrew the supply connections.

A single-handle faucet does not have any hot or cold valves. So, all of your water connections will be part of the spout assembly. Whereas, the faucets that have built-in supply lines, the mounting hardware will directly slide over them.

Your old kitchen faucet may have a diverter. It means, your faucet will also have a separate supply line that connects between the spout and the side sprayer. Your job is to disengage this connection.

Get the faucet-removing tools:

While removing your old faucet, you may find difficulty. That is, hard to reach the right space and gain enough leverage to remove the connections. But don’t worry. Using necessary can make your task easier.

Firstly, get a basin wrench. It contains a ratcheting head with teeth. It helps in holding a grip and reaching retaining nits behind the sink. Alongside, a basin wrench pivots 90 degrees allowing you to turn the handle from below.

Use this basin wrench to remove the diverter that is connected to the sprayer. If you are not using your old faucet again, you can cut its pipe with a tubing cutter.

Next, you will need a faucet and sink installer. It is a multipurpose tool designed for different sink applications.

Remove The Old Faucet:

A single-handle faucet will typically have mounting hardware connected to a single shank. This shank contains hot and cold supply lines. In a two-handle faucet, the mounts are placed over the valves.

You will need to remove all of the mounting hardware to remove the faucet. Usually, the nuts get rusted as they are kept idle for a long time.

Don’t worry, use some oil on them to get smooth You may need to apply it several times and leave it for soaking. Then, the mounting hardware will be loosened.

After removing the mounting hardware, the faucet should lift out. If the caulk seal doesn’t break, apply some force to it. When you are finished, clean your sink area thoroughly with an approved cleaner.

Determine Your Needs For Your New Faucet:

There are numbers and placement of the holes in your sink’s countertop. This will determine the type of needs for your faucet.

Your faucet may have one to four holes.  The fourth hole is typically used for a sprayer or a soap dispenser. The distance between these holes is called the spread. And you can determine your spread by measuring between the centers of the three main holes. An eight-inch spread is the most common.

Choose A New Faucet:

A center faucet is one where the handles and spout are part of a single unit. Whereas, a two-handle center set has separate hot and cold handles. These handles are connected to the base. They fit easily on the outside holes.

A single-handle faucet has a handle connected directly to the spout. It can be easily mounted to the countertop for a one-hole installation. But if you want you can go with an escutcheon plate. It will help in covering the two outside holes.

A widespread faucet is also a good option. Here, the faucet and the handles have separate units. You can install it with any spread. Since we are not going to install a sprayer, a single-handle faucet would be the best pick.

Install The Faucet:

We will install it with an escutcheon plate. In this case, the hot and cold supply lines are built directly into the faucet. It will also have a diverter which will connect to a side sprayer. But we are not going to install any side sprayer.

Now, we will place a faucet gasket onto the spout base. Then slide the base over the supply lines and onto the faucet body.

Make sure all the components are together properly:

You won’t need the escutcheon plate if you are doing a one-hole installation. But if you are doing a three-hole installation, you will need that escutcheon plate. Because you will be covering up the two holes with it. Hopefully, there will be a gasket as well to seal the gap between the escutcheon and the countertop.

Anchor The Single-Handle Faucet:

In this step, you have to place the gasket onto the underside of the escutcheon plate. Then slide it over the supply lines and on the shank of the faucet. Now it is ready to be placed on the mounting surface.

The escutcheon plate will help you to cover the first and third holes.

The mounting hardware connected to the shank has a washer that goes against the countertop and the mounting nuts. These are tightened up with three mounting screws.

Screw the nut up until it’s a half-inch below the surface. Then tighten up the mounting screws evenly.

Attach The Supply Lines:

Now it is time to attach the supply lines. You will see your single-handle faucet comes with built-in supply lines. They will be labeled as hot and cold supply lines. Connect these lines with the corresponding water supply valves.

After connecting them, attach the other end of the corresponding water supply valve coming out of the wall.

Now take a small strip of Teflon tape and wrap it around each thread. Then screw on each nut by hand and tighten them up with an adjustable wrench.

Also, secure the pipe of the eater supply valve running out into the wall. This will reduce the risk of any damage.

Turn On The Water:

Since everything is connected now, it is time to turn the water on and check if everything is okay. If you see any sort of drips or leaks, just tighten up the connections more properly. And lastly, remove all debris and flush the lines.

Frequently Asked Questions

How To Remove The Sprayer Hose From The Kitchen Faucet?

Firstly, turn off the water supply valves and lose their connections with the pliers. After disconnecting the sprayer hose, twist the threaded brass on the hose’s male threads and tighten up the cap. Then remove the mounting nuts by loosening them and take out the sprayer support and the sprayer.

What Can We Use To Cover The Sink Sprayer Hole?

To cover the sink sprayer hole, you can use an in-counter soap dispenser, garbage disposal switch, glass rinser, lotion dispenser, etc.

Final Thoughts

Hopefully, you now know how to install a kitchen faucet without using the sprayer. And you must have understood that connecting the sprayer is the only thing you have to skip here.

Other than that, removing the connections and the old faucet is to be attempted first. Then you can go with attaching a new faucet without installing its sprayer.

So this was all. Thanks for reading!